陰極金屬發泡材厚度與流道設計對高溫型質子交換膜燃料電池之影響;The Effect of Cathodic Metal Foam Thickness and Flow Channel Design for HT-PEMFC

NCUIR > Engineering College > Graduate Institute of Mechanical Engineering > Electronic Thesis & Dissertation > Item 987654321/72470

Please use this identifier to cite or link to this item: http://ir.lib.ncu.edu.tw/handle/987654321/72470

Title:	陰極金屬發泡材厚度與流道設計對高溫型質子交換膜燃料電池之影響;The Effect of Cathodic Metal Foam Thickness and Flow Channel Design for HT-PEMFC
Authors:	江建叡;Chiang,Chien-Jui
Contributors:	機械工程學系
Keywords:	金屬發泡材;高溫型質子交換膜燃料電池;流道設計;metal foam;HT-PEM fuel cell;flow channel
Date:	2016-08-29
Issue Date:	2016-10-13 14:58:28 (UTC+8)
Publisher:	國立中央大學
Abstract:	本研究探討金屬發泡材在不同壓縮量之滲透率、孔徑大小與孔隙率等物理特性，並將研究之發泡材應用於高溫型質子交換膜燃料電池，藉由使用不同壓縮量之發泡材與流道設計之搭配，來了解對電池性能之影響，以及針對反應氣體背壓、空氣當量比、加濕與操作溫度等參數研究，分析電池性能的變化。最終目的是找到提升電池性能之方法。研究結果顯示，在金屬發泡材的物理特性實驗中，能得出在低流速下，滲透率與壓縮率之關係呈非線性，其關係圖和孔洞面積與壓縮率之關係圖相似，表示滲透率與孔洞面積之關係連結。而在燃料電池研究上，指出較高的發泡材凸出量造成電池性能在高負載下衰退，因其金屬肋填充了觸媒層，反應氣體不易導入，讓水氣排出；發泡材深度變動對電池性能未有提升效果，但搭配適當導流設計能有效提升性能，以發泡材深度加厚及進出口導流加大加寬之設計搭配最佳，與單純對發泡材加厚有18.4 %的提升幅度；在參數討論之結果顯示提高背壓、空氣當量比、加濕與操作溫度皆能提升燃料電池，但加濕測試結果指出太高的加濕將對電池產生反效果。 ;In this research, the metal foam physical properties of different compressed thicknesses such as permeability, pore size and porosity were measured. Then, these metal foams were applied and matched with different types of flow channel on the high temperature proton exchange membrane fuel cell. Then, these fuel cells did the polarization tests and electrochemical impedance spectrum tests to realize the effect of metal foams and flow channel. Moreover, the operating parameters such as back pressure, air stoichiometry, humidification and temperature were tested to analysis the effects of fuel cell. Finally, the purpose of this study is finding the ways to improve the fuel cell. The results show that the relation between the permeability and compressed ratio are not linear in low mass flow rate at the measurement of metal foam physical properties. In addition, this relation is similar to the relation between porous area and compressed ratio. Then, it also shows the relation between permeability and porous area. The results of fuel cells show that the higher amount of metal foam protrusion has significantly declining the performance of fuel cell during higher loading operation. The reason is that reaction gas doesn’t easily flow into the catalyst layer to exhaust vapor by some parts of catalyst pores filling up metal foam ribs. Then, the thickness of metal foam does not improve the fuel cell performance but matching with appropriated flow channel make the fuel cell performance increase. The metal foams matched with bigger inlet and outlet channel width has the best performance which is 18.4 % higher than the origin flow channel. Finally, the parameters test show that increasing back pressure, air stoichiometry, humidification and temperature can improve fuel cell performance. However, the higher humidification may make the fuel cell performance decrease.
Appears in Collections:	[Graduate Institute of Mechanical Engineering] Electronic Thesis & Dissertation

Files in This Item:

File	Description	Size	Format
index.html		0Kb	HTML	429	View/Open

社群 sharing

Loading...