應用於毫米波封裝之覆晶連結分析與設計;Analysis and Design of Flip-Chip Interconnect for Millimeter-Wave Packaging Applications

NCU Institutional Repository > 資訊電機學院 > 電機工程研究所 > 博碩士論文 > Item 987654321/90144

請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/90144

題名:	應用於毫米波封裝之覆晶連結分析與設計;Analysis and Design of Flip-Chip Interconnect for Millimeter-Wave Packaging Applications
作者:	高嘉宏;Kao, Chia-Hung
貢獻者:	電機工程學系
關鍵詞:	π字模型;覆晶;曲線擬合;毫米波;T字模型;校正;金屬凸塊;π-model;Flip-chip;Curve fitting;Millimeter-wave;T-model;Calibration;Solder bump
日期:	2022-09-26
上傳時間:	2022-10-04 12:12:16 (UTC+8)
出版者:	國立中央大學
摘要:	本論文分為四個部分，第一部分(第一章)為介紹研究毫米波封裝的背景與動機，接著介紹封裝的類型與用途，最後說明研究毫米波封裝的方法與目的。第二部分(第二章)吾人參考許多相關文獻，其中內容大部分多為利用π字模型(π-model)建立覆晶(Flip-Chip)封裝連接處之等效電路模型，而電路中的元件值則是針對該物理尺寸利用曲線擬合(Curve fitting)的方式計算該元件值。此種常見方法仍具有侷限性，當結構參數不同時，則會出現函數選取不當，進而產生不具有物理意義的元件值。吾人將重新分析如何在毫米波(Millimeter-Wave)頻段下，建立覆晶封裝結構的T字模型(T-model)以及該如何有效萃取具有物理意義的元件值，進而與全波模擬以及實務量測比較散射參數(S-Parameters)之差異。第三部分(第三章)為吾人利用MATLAB程式碼運算，並提出一簡易的校正方法，首先針對參考文獻所提出的公式進行說明，接著搭配實作電路的特性，利用公式化簡計算。校正方法則先提出計算流程的原理，並將訊號流程圖(Signal flow)以傳輸矩陣表示。背對背串接的結構(即全電路)中左半電路(或右半電路)具有左右兩端的饋入結構，吾人利用自行編譯的程式碼進行計算去除兩端的饋入結構(Feeding structure)對於電路的貢獻，進而得出金屬凸塊(Solder bump)與和其連結的導體的響應。第四部分(第四章)則是將覆晶連結的封裝結構進行實作，其中實作版本依照量測頻率上限分作為10 GHz版本與40 GHz版本。首先吾人會說明製作兩種版本電路的原因，而後再提出兩種實作的結構參數分析與設計，並利用第三章的校正方法校正40 GHz版本，而10 GHz版本因實作原因未做校正，最後將理論計算(ADS)、全波模擬(HFSS)與實務量測進行校正前後的散射參數疊圖驗證，並比較理論計算、全波模擬與其之間散射參數的差異。第五部分(第五章)將前四章所述做結論，並說明10 GHz版本實作過程中所遇困難，並構想該如何在未來做改善，40 GHz版本則因量測結果與全波模擬有一小段差異，於此章歸納問題，並構想可能解決的方法做為未來工作。 ;This paper is divided into four Chapter. Chapter 1 introduces the background and motivation of studying millimeter-wave packaging, followed by the types and applications of packaging, and finally the methods and objectives of studying millimeter-wave packaging. In Chapter 2, we refer to many related papers, most of them use the π-model to build the equivalent circuit model of the flip-chip interconnection, and the component values in the circuit are calculated by curve fitting for the physical dimensions. This common method still has the limitation that when the structural parameters are different, the function is not selected properly, and then the component value is not physically meaningful. We re-analyze how to build the T-model of flip-chip interconnection in the millimeter-wave and how to extract the physically meaningful component values effectively, and then compare the differences of the scattering parameters with the full-wave simulation and practical measurements. In Chapter 3, A simple calibration method is proposed and demonstrated by using MATLAB code. The formulae in the references are used, and then the calculation is simplified based on circuit characteristics. In the calibration method, signal flow is represented as a transmission matrix by using the principle of calculation flow. In a back-to-back series structure, the left half-circuit (or the right half-circuit) has a feeding structure on the left and right ends, and we can use the code proposing in MATLAB to calculate the contribution of the feeding structure to the circuit by de-embedding the feeding structure on both ends, and then derive the response of the solder bump and the conductor connected to it. In Chapter 4, it outlines the fabrication of the flip-chip interconnection structure, and the fabricated version is divided into 10 GHz version and 40 GHz version according to the upper limit of the measured frequency. Firstly, the reasoning for making the two versions of the circuit was explained, and then we present the analysis and design of the structure parameters for the two implementations, and use the calibration method in Chapter 3 to calibrate the 40 GHz version, while the 10 GHz version is not calibrated due to its practical implementation. Finally, the scattering parameters of the theoretical calculation (ADS), the full-wave simulation (HFSS), and the practical measurements are verified by overlaying them with each other. In Chapter 5, concludes the previous four chapters and describes the difficulties encountered during the implementation of the 10 GHz version and considers how to improve it in the future, while the 40 GHz version has a small discrepancy between the measurement results and the full-wave simulation, and this chapter summarizes the problems and considers possible solutions for future work.
顯示於類別:	[電機工程研究所] 博碩士論文

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	67	檢視/開啟

在NCUIR中所有的資料項目都受到原著作權保護.

社群 sharing

資料載入中.....