中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/95547
English  |  正體中文  |  简体中文  |  全文筆數/總筆數 : 80990/80990 (100%)
造訪人次 : 42716072      線上人數 : 1419
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜尋範圍 查詢小技巧:
  • 您可在西文檢索詞彙前後加上"雙引號",以獲取較精準的檢索結果
  • 若欲以作者姓名搜尋,建議至進階搜尋限定作者欄位,可獲得較完整資料
  • 進階搜尋


    請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/95547


    題名: 應用於光耦合隔離系統之發送端雜訊整形 類比轉數位轉換器;A Design of Noise-Shaping ADC for Optical Coupling Isolation Applications
    作者: 陳琮元;Chen, Tsung-Yuan
    貢獻者: 電機工程學系
    關鍵詞: 類比轉數位轉換器;連續近似類比數位轉換器;雜訊整形;浮動逆變放大器
    日期: 2024-03-22
    上傳時間: 2024-10-09 17:00:15 (UTC+8)
    出版者: 國立中央大學
    摘要: 隨著科技的發展現在正處於第四次工業革命,即工業4.0。主要著重於互聯性、自動化、機械學習和實時數據等方面。透過智慧技術、演算法和控制機械等實體設備為自動化監控和分析技術帶來革新。在近年來的工業控制產品,如交流伺服馬達控制器,工業自動化逆變器,用於再生能源的功率調節器,都需要更高的效率與精度。在工業設備中,精確測量來自物理傳感器的信號是控制系統的關鍵部分,從測量方面來看,不僅需要最大的精度且還需要確保安全性與可靠性,工業控制系統通常在危險的電壓下運行,因而廣泛需要隔離器來保護人員和相鄰的電子設備。本電路以高精準度、低功耗為目標對隔離器中的類比數位轉換器進行設計。
    本論文實現應用於光耦合隔離系統之發送端類比數位轉換器,對於應用分為三角積分類比數位轉換器(Sigma-Delta ADC)與雜訊整形連續近似類比數位轉換器(Noise-Shaping Successive Approximation ADC,NS-SAR ADC)兩種類比數位轉換器,三角積分類比數位轉換器主要由三角積分調變器(Sigma-Delta Modulator, SDM)與數位降頻率波器組成,而雜訊整形連續近似類比數位轉換器以三角積分調變器轉換技術為基礎,其特性為在轉換過程中使用雜訊整形(Noise-Shaping)技術,以提高轉換精準度並降低功耗。
    本電路採用台積電0.18μm CMOS 1P6M製程,晶片面積分別約佔0.556 mm2與1.291 mm2,電源供應電壓分別為1.8V與1.2V,整體電路功耗分別為4.58 mW與317 μW,電路頻寬分別為40 kHz與200 kHz,電路採樣頻率分別為20.48 MHz與3.2 MHz。都以開關電容架構下實現解析度為12 位元。
    ;With the development of technology, we are currently in the midst of the Fourth Industrial Revolution, known as Industry 4.0. It primarily focuses on aspects such as interconnectivity, automation, machine learning, and real-time data. Innovations in automation monitoring and analysis technologies are brought about through smart technologies, algorithms, and control mechanisms for physical equipment. In recent years, industrial control products such as AC servo motor controllers, industrial automation inverters, and power regulators for renewable energy require higher efficiency and precision. In industrial equipment, precise measurement from physical sensors is a crucial part of control systems. From a measurement perspective, not only the maximum accuracy is required, but also safety and reliability must be ensured. Industrial control systems typically operate under hazardous voltages, necessitating the widespread use of isolators to protect personnel and adjacent electronic equipment. This circuit aims to design analog-to-digital converters in isolators with high precision and low power consumption.
    This paper implements analog-to-digital converters (ADCs) for use in optically coupled isolation systems at the transmitter end. For applications, it is divided into two types of ADCs: Sigma-Delta ADCs and Noise-Shaping Successive Approximation ADCs (NS-SAR ADCs). Sigma-Delta ADCs are mainly composed of Sigma-Delta modulators (SDMs) and digital decimation filters, while NS-SAR ADCs are based on Sigma-Delta modulation technology. Their characteristic lies in the use of noise-shaping techniques during the conversion process to improve conversion accuracy and reduce power consumption.
    This circuit is implemented using TSMC′s 0.18μm CMOS 1P6M process, with chip areas approximately 0.556 mm2 and 1.291 mm2 respectively. The power supply voltages are 1.8V and 1.2V, with overall circuit power consumption of 4.58 mW and 317 μW respectively. The circuit bandwidths are 40 kHz and 200 kHz, and the circuit sampling frequencies are 20.48 MHz and 3.2 MHz respectively. A 12-bit resolution is achieved using a switched capacitor architecture.
    顯示於類別:[電機工程研究所] 博碩士論文

    文件中的檔案:

    檔案 描述 大小格式瀏覽次數
    index.html0KbHTML22檢視/開啟


    在NCUIR中所有的資料項目都受到原著作權保護.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 隱私權政策聲明